video tutorials about soldering and desoldering are here.
more soldering tutorials here.
parts labeled visually:
note: the 2×5 header is not included in the kit and is not needed for normal operation. it’s helpful if you plan on reprogramming the firmware (which you more than likely will not be doing.)
each part has a corresponding location on the board which is marked in white text. there are only a few places where you can insert something backwards, and i’ve tried to highlight these parts with big red arrows. the order of parts soldering presented here is suggested based on part height (lowest to highest) which makes for easy assembly (parts won’t fall out when you flip the board over against the table, so you don’t have to use tape, etc.) here we go.
iset resistor and crystal
bend leads of resistor, insert, solder, inspect, clip leads. the orientation of these parts doesn’t matter.
74HC164 and 75HC165
super super important! make sure the half-circles match! don’t put this in backwards, you’ll be very sad later.
you’ll see on the board they’re marked as LS parts, disregard this. you might have trouble getting the leads into the holes, so bend all of the legs on one side just slightly by tilting the part against a hard surface.
important! the dot must go towards the outside as shown!
don’t insert the chips before soldering these parts. note that these parts are theoretically optional, though we highly highly suggest using them, which will make fixing problems much easier, in addition to swapping your firmware physically with a new chip, or replacing a burned out driver, etc.
again, line up the half-circles. this sockets have more of a square bite than a half-circle.
the orange ones, 0.1uF and 22pF respectively. the 22pF have a small “2” whereas the 0.1uF have a small “1” on them. orientation doesn’t matter. insert, bend leads, solder, clip. solder hot and quickly, as the ground planes will sink your heat (solder will cool faster than you’d like.)
the black can, marked 10uF.
do not insert this backwards! the white line is (-) which is the short lead. insert the long lead into the (+) side.
headers and UM245R
the headers are were the key and led matrices connect. the 5×2 is for jtag programming, which you don’t need if you’re never going to use it.
the UM245R is gives us USB. aren’t you glad you didn’t have to solder that surface-mount chip? don’t change the jumper positions, it won’t work if you do.
arrange your board as shown. the long leg of the led must be on the left, with the board in this position. insert leds and bend the leads to the opposite sides while holding the led in place. take care aligning each led.
Maybe a helpful tip that might save you some time and frustration (It did for me):
Load ALL leds correctly as described above (long and short leg) while holding the board (faceplate facing you) at a 60-90 degree angle from the table.
When they are all inserted, take a sheet of paper and hold it in front to the “led side” (so they don't fall out of their holes) while laying it gently face down on the table with the legs sticking up (see picture below). When it's on the table, push and shake alittle so that every led finds an “ok position”. They don't have to be perfectly aligned..you'll correct this later.
Now solder on one leg (on each of the 64 leds). Don't (do not) solder both legs! This is just to hold them in place. Once that is done, lift the board up to the 90 degree angle from the table. Hold the board with the left hand (if you are right handed) while pushing one finger on one led (with the same left hand), while you solder the led's leg with your right hand from the other side. Once the solder melts, you find that the led finds its own “naturally aligned position” when you apply pressure. The led can get quite hot, but you will survive (or adapt to the speed of soldering).
If it doesn't automatically “drop” into a natural position when the solder melts, you just have to push slightly in a different direction with your finger on the left hand. Once it's aligned, move on to the next led.
When they are all “re-soldered” on just one leg, flip the board around and check if they are all aligned. Fix the ones that are a bit tilted. When everything looks good, put the board on the table face down again (leds down, like the picture) and solder the other (second) leg on each led.
Done. Now just cut the legs off right above the solder.
— Evelon 2008/12/14 05:36
for soldering the diodes we suggest first putting a dab of solder on one pad, then place the diode with tweezers while that first dab of solder is hot. then you can go back and solder the other leg.
solder on the headers last, otherwise they’ll make assembly more difficult.
ribbon connection to grid pcb
first look here: help
then post any problems to the forum
once you've fixed your problem, please add it to help
logic board dimensions are 2.6” x 3.4” and height is 0.75” (the usb port being the highest point.) you might be able to do some creative modification to lower this height requirement (such as removing the standoffs from the ftdi breakout board or replacing the type A port with a type B).
→ archived discussion: here
what color? (nm value, google “visible spectrum”) what size? (you want T1 = 3mm) how bright? (higher mcd = brighter)
on print version of the jameco catalog, all of the standard and medium brightness leds that are T1 (3mm) will work just fine. some of the super-brights might also work.
here are some suggested part numbers from jameco
note that 137411 has a Vf of 4.8, this won’t work! get led’s with a Vf at or below 3.5 to be certain, though i’d be curious to have someone test out higher Vf leds. just get a few, test them out without soldering them in.
more leds, brighter:
this list takes the form:
'dk' = http://www.digikey.com/
'maxim' = http://www.maxim-ic.com/
'ftdi' = http://www.ftdichip.com/
'jameco' = http://www.jameco.com/
1 ftdi um245r ftdi um245
1 atmega32-16pu dk ATMEGA32-16PU
1 max7221cng+ maxim MAX7219CNG+
1 74hc164 dk 296-8248-5-ND
1 74hc165 dk 296-8251-5-ND
1 sip-10 res net dk 770-101-R100KP-ND
1 cry16mhz hc49/us dk X1103-ND
3 0.1u cap jameco 151118
2 0.22p cap jameco 15407
1 10u cap dk P975-ND
1 10k res jameco 691104
1 dip40 socket jameco 683227
1 dip24 socket jameco 683163
2 8×2 header jameco 117917
1 5×2 header jameco 117917
64 diodes dk 1N4148WTPMSTR
2 8×2 rt-headers jameco 139563
2 ribbon cable jameco 37671
4 ribbon con jameco 119467